Nicolaudie Architectural Forum

This afternoon (Tuesday) I did as your asked to set the timing parameters to the recommended settings. Before I did this I wrote down the numbers that have been set since I got the unit. They were: Mark Before Break = 0 Break = 176 Mark after Break = 16 Mark between slots = 0 After the change they a...

Well I was able to put in the new SD card into the unit on Thursday Aug 20. It was fine on Friday but when I went in on Sunday Aug 23rd it had failed and stopped sending the DMX data. Here is a recap on what's happening after the failure. All things seem to work on the unit. The trigger data respons...

Just to rewind a few steps. You are right. When I disconnected the HE-10 port and set it to a scene which did a slow fad in 2 changes, It worked fine. This ran for 4+ days and when it was checked at the end, it was still fading just as I left it when I started the test. You asked me to reformat the ...

Well even with my changes in my software, it failed after 1 day. I am at a loss as to where to go from here. Ben - Have you been able to test changing a lot of scene changes from the HE-10 port at your location. I don't think this issue would be a problem with the SLEA-UE7 hardware since all the lig...

Wouldn't you know it that my change wasn't doing what it was supposed to do. It never released the last switch trigger value. Reprogrammed it again and tested if the release was being done right. Its good now. Will wait again for a few days. While going thru the code I noticed something else I shoul...

Not good news. On Sunday night (Aug 9) I went in and all was working fine. But when I went in Monday morning the DMX had stopped. I will have to verify that my software is doing what I intended at the HE-10 port using the USB connection and monitoring the HE-10 bits using the HARDWARE.EXE software. ...

Well its the end of the day on Aug 7 and I made the change to my PIC controller. When a trigger value is output to the HE-10 port it will stay there for 250ms and won't be changed. Then the HE-10 signals will be all set high for another 250 ms which will be like releasing the buttons. After this cyc...

Well its been 4 days and the SLEA-UE7 is outputting DMX data just fine. It was running a scene that faded back and forth between 2 patterns. It must be problems in outputting the scene changes using the HE-10 interface since this was disconnected 4 days ago. My next step is to change my PIC controll...

I went into Organ Stop Pizza this Sunday night and sure enough, the DMX traffic had stopped. At this point I disconnected the HE-10 dry contact interface that changes the scenes and power cycled the SLEA-UE7. I will now wait for a few days and see if it still fails. For some reason my intuition thin...

I went and installed the link you provided. I was surprised at how long it took to do the “SSL Library” part of the install. I waited for about 8 minutes then decided to take a shower. When I came out it was done, thank goodness. When I go into work I will reinstall the firmware and then reboot the ...

This morning I went in and low and behold, the DMX output was not working. Before I did anything and with the router already connected, I just executed the HARDWARE.EXE command and it connected without any issue. At this point the SLEA-UE7 controller was talking to the fixture and sending out DMX da...

Will update the hardware in the near future when I go into work with my PC. You won't hear from me for a few days depending on what I find. I have been using the ESA2 software only. At this time I have the hardware installed but only 1 test fixture running in the back room.

We are currently having an issue with our SLEA-UE7 unit. Right now I have the unit running 24 hours/day in stand alone mode. It is running the Feb 12,2015 release. The problem is that after 2 or 3 days the DMX traffic to the lights just stops. This has been going on for quite some time but I didn’t ...

Thanks for responding Ben. I get the picture now. I didn't know how the tablet scene values relate to the standalone controller scenes. It might be nice to add a line to the documentation indicating that the scene values displayed on the 3 character display on the standalone hardware are the ones yo...

Thanks for the reply. I tried this about 2 weeks ago but didn't see anything that made sense for doing the scene select value. I went ahead and tried doing what you said just yesterday with the same results. On the top line of the Easy Remote button I am selecting "Select Scene On". When I...